Skip to content

DIY Jacks “R” Better Weather Shield

For the past few winters, I’ve been playing with “non-traditional” insulation options for extending my hammock camping in cold weather: vapor barriers, hammock socks, and top and bottom covers. This season I spent a lot of time designing and testing a hammock sock, but I was so irritated by the amount of condensation and frost that I abandoned it.

For me, finding the best solution for winter warmth is a balancing act. I prefer lightweight, multi-use gear, and while the sock I designed was light, it wasn’t multi-use, and I hate frost and moisture buildup. A bigger tarp would eliminate drafts, but could be heavier and bulkier (or costly, if I went with a ground-to-ridgeline cuben design). Plus, they take longer to pitch. Thicker and bigger down quilts for winter are  expensive, but I’d prefer to extend my 3-season quilts than invest in a winter set that wouldn’t get as much use[1. If I lived in an area where it was colder, I’d probably invest in a winter quilt set, but for most of my trips, a 20-degree rating is usually sufficient.].

Hammock socks can add about 10 degrees of warmth by trapping the air around the hammock and creating a wind block. Another technique that can achieve similar results is by using windproof, breathable covers around just the insulation—like a clamshell instead of a 360-degree sock. I turned my efforts to this “shell” approach to save weight and reduce condensation. These shells are often referred to as top and bottom covers, or simply weather shields. As the name implies, these shells can be used year-round, especially with waterproof materials, which can provide additional weather protection with smaller tarps, like the asymmetric tarps from Hennessy Hammock. An added bonus with weather shields is that your head remains uncovered, reducing or even eliminating any breath condensation issues.

I was still in do-it-yourself mode, so I went looking for some material to craft into shells for my quilts. I came across the Jacks “R” Better Weather Shield, which takes a DriDucks UltraLite2 Poncho and modifies it into a 3-in-1 poncho, under cover, and sleeping bag shell (or top cover). To my delight, the Jacks also sell a modification kit and the DriDucks poncho separately. I purchased both the mod kit and the poncho and set to work to create my own Weather Shield.

Jacks "R" Better Weather Shield

Image courtesy of Jacks “R” Better. This image shows the Weather Shield deployed as an under cover on a JRB Bear Mountain Bridge Hammock.

I have to compliment the Jacks on this design. First off, DriDucks rain gear has long been a popular choice as an inexpensive waterproof/breathable shell for backpackers and thru-hikers. It’s also field repairable with Duct tape, and it is extremely lightweight[2. Don’t get too excited. The DriDucks does have a drawback: it’s not super durable. As lightweight materials go, it’s not tissue paper, but I wouldn’t go bushwhacking in it.]. The Jacks’ design was deceptive at first glance: the image on their site look like it’s just an under cover, but they also include some Omni-tape (self-adhering Velcro, hook-and-loop ribbon) so the Weather Shield can convert into a sleeping bag shell or top cover. The completed kit weighs in at only 9.6 oz (272 g)[3. Trimmed down, it weighs only 8.8 oz (249 g)], which is lighter than most rain jackets. The kit is also very easy to make with only minimal sewing skills. All the materials were cut to size and ready to assemble so all I had to do was sew.

Since I’m a visual learner, I went to the drawing board to illustrate the Jacks “R” Better Weather Shield for anyone else who attempts this project or one like it. I should note that the Jacks “R” Better Weather Shield and kit versions do not come with suspension. This is because the Weather Shield is designed to fit the JRB quilts and eliminate a second set of shock cord. Jacks “R” Better does sell a stand-alone Under Quilt Suspension System, or you can fabricate your own.

DIY 3-in-1 Rain Protection

Using The Weather Shield

My first time using my DIY Weather Shield was during a two-day camping trip with my Boy Scout troop. It rained steady for both days, with temperatures just above the freezing point. I admit I was gloating a little about my hammock to some dads who tagged along. “Hammocks hang high and dry,” I prophesied. When I finally snuggled into my hammock for the night, I noticed my top quilt was wet in places. “It probably touched the ground while I was getting into bed,” I thought to myself. Later in the night I felt water droplets on my head that woke me to the fact that I had a problem. What I brushed off earlier as ground water had turned into a small puddle on my top quilt. The tarp I was using was seeping a lot of water through the ridge line, and if I didn’t act quickly, my insulation would be soaked; a bad proposition for winter camping (or any time of the year for that matter). I had rigged the Weather Shield as an under cover, but I unclipped it, cinched the foot end and connected the OmniTape to create a top cover. After tucking my top insulation into the foot box, I draped the top of the Weather Shield over my head and hammock.

I slept the rest of the night snug, warm, and dry. In the morning I was pleased to find the inside of my DriDucks poncho/Weather Shield was also dry—no condensation. The outside was another matter: the entire top cover was soaked with puddles of water everywhere, and rain still droned on outside. The Weather Shield saved my insulation and kept me from an emergency bail-out, or worse, admitting my hammock wasn’t a superior weather shelter.

Tips

  • A little weight can be saved (1 oz/28 g) by eliminating one cord lock on the poncho hood and consolidating the draw cord into a single cord lock.  Removing the built-in stuff sack also saves weight and garners another spare cord lock.
  • Fold then roll the Weather Shield and use a rubber band to keep it “packed.” Store in an outside pocket for moisture control and easy access.
  • Close all OmniTape/Velcro strips before packing to prevent damage and inadvertent “clinging.”
  • “DriDucks” uses 2-ply microporous polypropylene and is lighter than the “FroggToggs,” which uses 3-ply microporous polypropylene. Both are from the same company.
  • To seal off the hood: pull the hood inside the hammock; cinch the hood as tightly as possible, then wrap the draw cord around the hood to “goose neck” it. Finish with a simple Clove hitch.

13 thoughts on “DIY Jacks “R” Better Weather Shield”

  1. Pingback: Infographics: Hammock Camping and Tarps | Just Your Average Hiker

  2. I bought the JRB mod kit to put on my DD poncho and looking forward to starting the project (no sewing skills at all here). My question is how much warmth does this add alone as a sort of UQ (and I realize this is wildly subjective so I suppose I am asking just personal opinion)? I am new to hammock camping in general and wanting to pair this with my GT UL hammock and potentially a JRB 1/4″ torso pad. With the DD poncho mod only what temp rating would you give it? With the 1/4″ torso pad only? and finally with the 2 combined?

    1. I’ve been using the Weather Shield over the past week to coax a 30-degree quilt down to the twenties. It works. The shield by itself could be used in hot climates that have high diurnal shifts to keep you from getting cold butt syndrome. I would say with overnight lows in the 60s it would be enough for many people.

      Your other questions will be too speculative for me to answer. You’re going to have to test and see if they meet your conditions.

      When I first started hammock camping all I had was pads and sleeping bags. This worked in some pretty cold country in temps as low as 15 degrees. You can stack pads to boost warmth for colder conditions, just like you would for sleeping on the ground. I would recommend getting a $7 blue foam pad from Walmart and cut it in half, using one half turned 90-degrees to wrap around your shoulders while using your other pads under your torso (giving you double thickness in your torso and rear area) and a half pad under your legs.

      The Weather Shield really helps by cutting drafts and wind gusts, along with ground splashes and side-driven precipitation. By creating a pocket of dead air space between you and the hammock, the Weather Shield can add a few degrees (maybe as much as 10) of warmth.

      Always test in your backyard first to make sure your system is working well for you.

      1. Ah, got it now. You can see it in the bottom left part of the illustration where it’s connected to the guy line.

        One other question, in the PLUQ post comments you suggest that the method above is the best option for putting together the PLUQ if you want it to be multi-use as both a top and under quilt. I was curious, do you still fold it in half? If so, do you sew another grosgrain loop in the center of the short sides?

        Thanks,
        Alex

  3. in the PLUQ post comments you suggest that the method above is the best option for putting together the PLUQ if you want it to be multi-use as both a top and under quilt. I was curious, do you still fold it in half? If so, do you sew another grosgrain loop in the center of the short sides?

    1. If you want to make a poncho liner multi use, you wouldn’t fold it over for the top quilt. You would need to leave it very flexible.

  4. In your write-up, you had your bacon saved by using the poncho as an overcover – presumably letting the water enter the hammock bed. How did you keep your underquilt dry then?

  5. Pingback: Therm-a-Rest Slacker Hammock Warmer Review - The Ultimate Hang

  6. Cuales son las medidas de poncho abierto. Tengo que hacer uno con que tela me aconsejan hacerlo y que sea impermeable.

Leave a Reply to Therm-a-Rest Slacker Hammock Warmer Review - The Ultimate Hang Cancel reply

Your email address will not be published. Required fields are marked *

This site uses Akismet to reduce spam. Learn how your comment data is processed.